#Iei 212i keypad programming install#
#Iei 212i keypad programming manual#
#Iei 212i keypad programming code#
#Iei 212i keypad programming free#

#Iei 212i keypad programming code#

If you forgot the master code or it is not working, momentarily push SW1, (progra. With 4 independent outputs and 4 independent timers, the IEI 212i can support up to 120 different. IEI will not be liable to the purchaser or anyone else for incidental or consequential damages arising from any defect in, or malfunction of, its products. This is Door Gard Command IEI 212 keypad.The default master code is 1234. All programming can be performed from the front of the keypad. IEI’s sole liability is limited to the repair or (at IEI’s option) the replacement of the defective product or part when sent to IEI’s facility (freight and insurance charges prepaid), after first obtaining IEI’s Return Merchandise Authorization. Features: Flushmount, indoor design Front keypad programming Allows for up to 120 user codes. The i-style keypad mounts to most standard single-gang electrical back boxes. With 4 independent outputs and 4 independent timers, the IEI 212i can support up to 120 different user codes. IEI does not assume any responsibility for damage or injury to person or property due to improper care, storage, handling, abuse, misuse, normal wear and tear, or an act of God. All programming can be performed from the front of the keypad.

#Iei 212i keypad programming free#

(IEI) warrants its products to be free from defects in material and workmanship, when they have been installed in accordance with the manufacturer’s instructions, and have not been modified or tampered with.

On SE keypad, holes have also been spotted inside the front housing for additional LEDs (LEDs not included).

To speed installation of the SE keypad, holes have been spotted on the inside the back housing for mounting to a wall or a single-gang electrical box.

For use in extreme weather conditions, consult the factory for additional methods of protecting your keypad. IEI 212i Flush Mount Keypad Flush mount, single-gang design for easy installation into drywall, or single-gang electrical box 120 users Non-volatile memory.

This allows air to circulate and a place for condensation to drain.

Do not seal the drain holes at the bottom of the keypad housing. Case Dimensions: R Keypad: 3.75W x 5.25H x 2.50 D SE Keypad: 3.00W x 4.50H x 1.55D.

Do not silicone the cover plate because the unit will not seal properly. This helps prevent water from entering the case and condensing on the circuit board.

When mounting this unit outside, apply silicone to the area where the wires enter the case.

The bi-color LED provided with the SE keypad illuminates red when the LockRelease relay is de-energized and green when the relay is de-energized.

#Iei 212i keypad programming manual#

2120m/242em standalone keypad installation/ programming manual this equipment is.

Must be reset from inside the protected area. Keypads courtesy light can be always off, always on or be. IEI-283 SECURITY MODULE responds to tamper switch (included) and cuts all in/out power to the door lock.

To avoid ESD (Electro-Static Discharge) interfering with the operation of the keypad, ground the housing to earth ground. Iei 212I Keypad Programming Manual : Changing Code On Iei Key/.

If you cannot ground the power supply, then you must ground the keypad housing. Wire the transorb in parallel with the lock power terminals.Īlso, to avoid ESD (electro-static discharge) from interfering with the operation of the keypad, ground the negative terminal of the keypad to earth ground. If the keypad still does not work after troubleshooting, please call IEIs techinal support.

#Iei 212i keypad programming install#

To prevent electrical kick back voltage from damaging the keypad, when using an electrical locking device, you MUST install the transorb as close as possible to the lock. NOTE: This manual covers both the 212 and 242 model. TIMED EGRESS INPUT Upon a momentary closure, this normally open loop will trigger the main relay for the same time period as the Master Code. LED guidance makes programming easy, and changing codes a matter of seconds for an auth-o rized user.

Also, the voltage selection jumper on the main circuit board is no longer required. PROGRAMMING All programming is accomplished entirely from the front of the keypad. It is also possible to control the red and green chip LED’s externally, with an alarm panel for example, by using connector J1. The LED’s changed to surface mount chip LED’s mounted on bottom of the circuit board which eliminates the need for the wire harnesses. This product was re-designed using a new manufacturing technology, which changed the physical appearance of the keypad electronics.